• rus
  • eng
Выбрать раздел

LIME VERTICAL KILN, Shaft Lime Kiln PShI-150

LIME VERTICAL KILN, Shaft Lime Kiln PShI-150
LIME VERTICAL KILN, Shaft Lime Kiln PShI-150 - фото 1
Обновлено: 2 марта 2023, 08:51 ID: 1637
1 /штука
на Флагма с 4 октября 2018
Вара Роман Іванович


General Information:
- shaft lime kiln PShI-150, hereinafter - kiln, is a process equipment for the sugar industry and is designed to produce lime and carbonatation (kiln) gas in sugar factories by means of limestone calcining.
Technical performance on СаО 150 t/hour
Limestone calcining degree 90-92

The kiln is supplied unassembled in individual components according to the Table 1.
Table 1. Components of kiln PShI-150
1. Loading and distribution device
2. Discharging device
3. Barrel of skip hoist
4. Bucket of skip hoist
5. Shaft
6. Ladders and service platforms
7. Bearing member
8. Skip hoist winch

- On request of the Customer (Buyer), incomplete supply of kiln components and equipment is possible.
- Automation and control means are not included into kiln scope of supply (supplied separately).
- Lining, insulation materials are not included into kiln scope of supply (supplied separately).
Brief operation description: The shaft lime-gas kiln IPN-150 is a cylindrical shaft, lined inside with insulating and refractory bricks
The kiln lining ends on the level of the loading chute. Top of the lining prevents the baffle shell from destruction when kiln is charged.
To ensure the strength of the construction and to prevent the atmospheric air inflows, the shaft is enclosed within a metal enclosure, welded from steel sheets. The lower part of the shaft is cone-shaped.
The kiln shaft is supported by four supports located on the foundation.
Top of the shaft is closed with a flat sheet steel slab. The removal of kiln gas is carried out through the annular gas discharge duct created by the gap between the baffle shell and kiln lining.
At the top of kiln on the flat slab, loading and distribution device is mounted, consisting of a receiving hopper with a shutter cover and swivel chute. The uniformity of charge distribution in the kiln is provided by the swivel chute.
For discharging the lime from the kiln, at the bottom of the lower cone part of the shaft, a discharge unit mounted. Lime is discharged into a hopper located under the kiln, ‘table’. The drive transmits reciprocating motion to the ‘table’. By changing the frequency of the reciprocating oscillations, the discharge intensity can be regulated.
The kiln is charged with the bucket skip hoist.
In the barrel of skip hoist there are doors, to which the transition platforms from the kiln shaft platforms are connected, serving simultaneously as supports for skip hoist barrel. At the levels of kiln service platforms, in the shaft there are hatches to perform the lining and repair works.
Filling the bucket with a charge is controlled by an automatic control system.
The loading and distribution device should provide a reliable seal of the shaft and uniform distribution of limestone and fuel in its horizontal section. The gas removal conduit is located below the charge loading level, creating a rarefaction required for the inflow of air through the discharge unit in an amount required for fuel combustion in a combustion zone.
The discharge unit provides a uniform lime selection at a given temperature: both in time and in the section of the shaft, and also provides uniformity of air-sweeping through the shaft section.

Наиболее свежая информация находится у владельца объявления.
Работает на Флагма с 4 октября 2018
Вара Роман Іванович
Смотрите еще объявления в категории Производственные линии
Вара Роман Іванович
Скажите, что нашли объявление на Флагма
Правила безопасности: Не соглашайтесь на предоплату, если не уверены в надежности пользователя.
Написать сообщение
Техенергоцентр, ТОВ Вара Роман Іванович, Директор
LIME VERTICAL KILN, Shaft Lime Kiln PShI-150
1 €/штука ID: 1637
Выбрать раздел